# Pierce County Wind Speed & Snow Load Roof Requirements | Tacoma Roofing

> Pierce County's ground snow load and soil-class assumptions for roof structural design, and why the exact design wind speed should be confirmed for your property.

URL: https://tacomaroofing.net/guide/pierce-county-wind-speed-snow-load-roof-requirements/

Pierce County Code sets ground snow load at 25 psf for elevations up to 700 feet, and assumes Site Class D soil county-wide absent a soils report. The exact design wind speed for your property should be confirmed with the City of Tacoma or Pierce County building department, since it varies by elevation and isn't a number worth guessing at.

Two numbers govern how a roof structure in Pierce County has to be built to code: snow load and design wind speed. One of those is clearly published. The other needs a direct confirmation call, and here's why we're telling you that instead of guessing.

## What's actually confirmed: ground snow load

**Pierce County Code sets ground snow load at 25 pounds per square foot for elevations up to 700 feet.** This is the load a roof structure has to be designed to carry from accumulated snow, and it's a standard, published prescriptive value for most of the county's populated, lower-elevation areas — including Tacoma itself. Properties above 700 feet in elevation fall outside this prescriptive number and require a site-specific engineering analysis instead, since snow load increases with elevation.

## What's actually confirmed: soil classification

Pierce County assumes **Site Class D** soil county-wide for structural design purposes, absent a project-specific soils report showing otherwise. This factors into the broader structural engineering calculations for a building — it matters more for new construction, additions, or significant structural roof changes than for a standard like-for-like re-roof, but it's part of the same code framework.

## What we're not going to state as fact: design wind speed

You'll find a **110 mph** figure cited in various places as the prescriptive design wind speed for IRC-based structural design across the Puget Sound region. That figure is confirmed for **Snohomish County**, a neighboring jurisdiction — but it was not independently confirmed specifically for Pierce County in our own research, and design wind speed is exactly the kind of code number that can differ from one county to the next, and even by elevation and exposure category within the same county. Rather than repeat a neighboring county's number as if it were confirmed here, we're telling you directly: **the exact design wind speed for your property should be confirmed with the City of Tacoma or Pierce County building department** before it's used in any engineering calculation or permit application. That's not us being evasive — it's the honest state of a real code citation, and getting it wrong on a structural document is a genuinely bad outcome we'd rather avoid than paper over with a borrowed number.

## Why wind exposure still matters here regardless of the exact number

Whatever the precise code figure turns out to be for your specific property, Tacoma's physical exposure is not in question — the city sits directly on open Puget Sound water at Commencement Bay, with the Tacoma Narrows channel nearby, the same channel whose winds famously destroyed the original 1940 Narrows Bridge. That's a real, qualitative reason to specify wind-rated underlayment and correct fastening on a roof here, independent of exactly which mph figure the code lands on for your address.

## What this means for a standard re-roof

Most standard residential re-roofs in Tacoma are permit-exempt under the city's rules (see our permit-requirements guide) and don't trigger a fresh structural wind-speed calculation — the underlying structure isn't being redesigned. Where this actually comes into play is new construction, additions, structural roofline changes, or any project that requires an engineer's stamp.

## Bottom line

Pierce County's snow load (25 psf up to 700 ft) and soil-class assumption (Site Class D) are confirmed and published. The design wind speed is not something we'll state as settled fact here — confirm it with the City of Tacoma or Pierce County building department for your specific property and elevation. Call **(253) 201-1336** and we can help you get connected to the right department for that confirmation as part of your project.

## FAQ

**Why won't you just publish the design wind speed number?**

Because getting a code citation wrong is worse than not having it — a specific design wind speed can vary by elevation, exposure category, and which edition of the code applies, and we'd rather send you to the building department for a number tied to your exact property than publish a figure that might not hold up when you actually pull a permit.

**Does the 25 psf snow load apply to my property regardless of elevation?**

It applies up to 700 feet in elevation under Pierce County Code. Above that, a site-specific engineering analysis is required rather than the standard prescriptive number — worth checking if your property sits at higher elevation within the county.

**What is Site Class D, and why does it matter for a roof?**

Site Class D is a soil classification used in structural design calculations — Pierce County assumes it county-wide unless a soils report says otherwise. It factors into the broader structural engineering for a building, and matters more for new construction or major structural roof changes than for a standard re-roof.